Skip to contentBlack Friday20% off Lite and Core, 35% off Pro · until 30 NovemberSee prices
CAGE MOLD
08

Numbers and labels

Cage Mold works out how much silicone and how much casting material you need, and writes it on the action card and on the printed parts. These figures are in the Core and Pro packages; on Lite these figures read CORE and no label is engraved on the parts.

NumberWhereHow it is worked out
MasterThe action card, the Generator panelThe model's bounding box, X × Y × Z, in mm. With an object selected the figure shows its name and size.
CastingThe action card; Watermark › Casting Volume; the grip pocket's floor on a trayThe model's own volume (ml). Known as soon as a model is chosen. Multiplied by the cavities in a Two-Part mold; the sum of all copies with Grid.
SiliconeThe action card; the label tab on box part 01's foot; the grip pocket's wall on a tray (the rim's top without a grip)The volume of silicone to pour × Silicone Density (g/cm³). Known once the mold is built; until then "—". With RTV-2 it is the total with the catalyst; the silicone and the catalyst apart are in Before the Pour and on the mold sheet ("Base 80.4 g + Catalyst 1.6 g"). With Silicone Type A/B it gives how much of each part to weigh ("A 125 g + B 124 g", by the Mix A : B). The model, the core and the air above the pour level are taken out of the volume; it is only the rubber really poured.
Plaster · SlipOn Slip Cast: the action card, the case parts' feet, the casting sheetThe plaster and water to mix ("3.67 kg + 2.57 L", at the Consistency) and the slip that fills the mold. Every case part carries its own plaster piece's amounts.
ShotOn Injection Mold: the action cardThe volume of the cavity, sprue and gate, and its weight at the plastic's Density ("4.2 cm3 · 3.8 g"). Known after Make Draft or Make Mold; until then "—".
CostThe mold sheet, under the parts to printWhat the silicone and the filament cost at the prices per kg you entered in the preferences; Core and Pro (below).
Confirmed at … mmThe status barThe detail the mold was computed at; it reflects Mold Detail. Smaller means finer detail.
Confirm's noteYellow text on the action cardAnything Confirm has to say: a core key made smaller, a hollow left without a core, a piece that could not join the mold, a wall made thicker, a pocket the silicone cannot reach; on Injection Mold a shot over Max Shot, faces that lock, sections over 6 mm thick that will sink, alignment pins that do not fit.
Two-component silicone. Choose Platinum (A/B) 1:1 in the Silicone section and, for another ratio, enter the maker's ratio by weight in Mix A : B (10 : 1…); the card gives how much of each part to weigh (7.1 Silicone). Add 5 % for losses.

What a mold costs

In Core and Pro, Cage Mold works out what a mold's material costs at your own prices. The prices are in Cage Mold's preferences (chapter 2) and start empty; an empty price prints no cost.

  • Silicone price per kg: what your silicone costs per kilogram.
  • Filament price per kg: what the filament costs per kilogram.
  • Currency: written before the amounts ($, €, TL…).

Type the price in figures alone, with a point or a comma before the decimals (450 or 12.50). Anything else brings "Enter a non-negative price or leave it empty" under the box, and that price is not used.

The amounts go on Export's mold sheet, under the parts to print (chapter 9): the silicone's cost, the silicone per cast (the silicone's cost ÷ Expected Casts), the filament's cost and the total of the costs entered. The silicone's comes from the silicone weight worked out when the mold is built, the filament's from the parts' weight as solid prints (volume × Filament Density). Slip Cast and Injection Mold give the filament alone. Lite prints no cost.